空調怎么驗貨？測庫10年資深技術主管講解空調驗貨標準與方法

TESTCOO/2021-10-22

炎炎夏日，怎么能少的了空調，那么空調是怎么驗貨的呢？測庫專業技術主管講解空調驗貨方法及標準。

一、電器分類

電熱器具：裝有電熱元件而不帶有電動機的器具。

電動器具：裝有電動機而不帶有電熱元件的器具。

聯合型器具：裝有電動機和電熱元件的器具

?二、電熱器具

電熱類有電熱水壺/電熱咖啡壺/電熨斗/三明治爐/多士爐/取暖器/烤箱等

電動類有吸塵器/打蛋器/攪拌器/電風扇/榨汁機等

聯合型器具有電吹風/加濕器等

大型家電有空調/冰箱/洗衣機/抽油煙機等.

三、空調大體有下面幾種:

1.分體式空調

3. 窗式空調

2.立柜式空調

4. 吊頂式空調

四、外觀注意事項:?

1. 如果是塑料件, 那需要注意壺身和底座的顏色是否一致. 有可能材料不一致而導致有色差, 那需要查看客人訂單, 參考樣品, 彩盒產品照片.

2. 塑料件注意飛邊, 縮水, 氣紋, 劃痕等外觀不良. 各個裝配部位縫隙應該均勻, 間隙不要大于0.8mm. 不要有松動/變形等不良現象.

3. 金屬件, 表面應該注意劃痕, 銹斑, 電鍍不良及指紋印等不良情況, 外觀應該符合客人訂單及樣品. (例如不銹鋼鏡面及啞光效果)

4. 最好大貨和彩盒照片放一起拍張照片.

五、空調驗貨基本測試:

1.Transportation drop test

No critical & Major issue found on package & product after (10 times) drop test according to the standard of ISTA 1A.

2.Product Size /power cord length / WeightMeasurement?(量尺寸的時候尺子拉直, 如果卷尺頭子有松動, 可以從10cm位置開始測量)

3.Bar code scan check

二維碼(app下載個二維碼掃描軟件, 可以掃描出鏈接, 如果不能連上, 拍鏈接照片備注即可)

4.Assembly/installation check

5.Full function check?(including the function which only can be checked after fully assembling/installation.)

6.Coating adhesive Tape Test

7.High voltage test

8.Power on the check?(The good condition samples should be operating at full load (preferable) at least 4 hours at rated voltage or time reference the user instruction if less than 4 hours.

after testing the samples should pass the hi-voltage check, function check, earth continuity check, etc., and no defect found.)

9.Earth continually test if applicable

10.Power consumption check

11.Power cord strain relief test

(如果沒有拉力器, 可以吊相應的重量, 這個測試最好不要備注沒有儀器)

12.Internal workmanship and critical component check.

13.Rubbing test?for rating label and adhesive Test for printing, marking, and logo

14.Stability test?(Appliances(other than fixed appliances and hand-held appliances)is placed in any normal position of use on a plane inclined at an angle of 10°to the horizontal, the supply cord resting on the inclined plane in the most unfavorable position.The appliance shall not overturn.)

15.Timer accuracy check?(timer should be set as per instruction manual and the actual time should be measured, the timer is set for 2 hours.if no client requirement, the tolerance requirement is: electronics type +/-1minutes, mechanical type +/-10%)then power off, and then power the unit on again with 10 seconds.)

16. Drop test for remote controller?(Freelydrop the unit through a height of 1000mm onto a smooth concrete floor with 3mmTvinyle tile 3 times by different position, check the product unit after each drop. Any malfunction /construction broken or other major defect be found.)

17. Gas leakage check?(use the gas detector to check the connection point between tube and compressor etc. gasline. no gas leakage found.)

18. Noise check?(apply rated voltage to the unit and operating at the highest setting, then measure the noise with the tester 1m away from the unit. the noise level should be within the requirement.)